The Virginia Graeme Baker Pool and Spa Safety Act (VGBA), effective December 19, 2008, imposes mandatory federal requirements for the avoidance of suction entrapment. One of the main components of the VGBA is the requirement of safety drain covers, and those covers have limited life spans.
Drain cover manufacturers are required to provide the consumer with information that tells them when the drain cover must be replaced before they begin to crack or show other signs of failure. Many manufacturers have designated a life span of 5 years, others up to 10 years.
It is time to check those covers.
All plastic drain covers, skimmer equalizer covers and spa suction outlet covers have a life span stamped on the cover.
Since numerous fittings were installed between 2008-09, many have or are about to reach the end of their stated life expectancy and need to be replaced.
Life spans of drain covers:
• DS 360: 3 years
• Aqua Star: 5 Years
• Paramount / SDX-Retro: 5 Years
• Hayward: cover, frame and screws must be replaced every 7 Years
• Waterway: 7 Years
• Lawson: 10 Years
• A& A: 10 Years
• Triodyne Anti-Hair Snare Drain Cover: 7 Years Safety drain covers are just one component of the VGBA. It is a good idea to take time to review other aspects of the law, to ensure that pools are in compliance.
The VGBA mandates the following changes in federal regulations for public pools/spas: ▪ All pool drain covers manufactured, distributed or entered into commerce on or after Dec. 19, 2008, must meet the ASME/ANSI A112.19.8 standard, or the successor standard ANSI/APSP-16 2011.
▪ All public pools and spas must be equipped with VGBA compliant drain covers.
▪ Pools and spas operating off of a single main drain (other than an unblockable drain) must also add one or more of the following options:*: ▪ A safety vacuum release system (SVRS); ▪ A suction-limiting vent system; ▪ A gravity drainage system; ▪ An automatic pump shut-off system; ▪ A disabled drain; or ▪ Any other system determined to be equally effective as, or better than, the others listed above.
*A pool may have more than one single main drain. If a pool has dual or multiple main drains more than 3 feet apart, it may be exempt from this final requirement. Pools and spas with single main drains that are unblockable are also exempt from this requirement.
What are unblockable drains?
The VGBA only authorizes a standalone single drain suction system that meets the definition of a unblockable drain.
An unblockable drain includes all components from the cover to the suction outlet pipe, including support structures, fasteners and their receptacles.
Unblockable drains are defined based on the sump size, which is the opening in the pool or spa finish behind the cover.
To qualify as unblockable, it must not be possible to shadow the sump opening with the 18 inch by 23 inch body blocking element of the ANSI/APSP16 standard. Unblockable drains can be one of the manufactured type or the field fabricated type that is certified by a registered design professional. While manufactured products can be of the blockable or unblockable type, registered design professionals are only authorized to design and certify the installation of unblockable field fabricated drain systems.
Another important difference between blockable and unblockable drain systems is how their flow ratings are calculated.
An unblockable system’s flow rating is the sum of all suction outlet fitting assembly flow ratings. A blockable drain system’s flow ratings are calculated based on the assumption that the flow through one suction outlet fitting assembly will be blocked.
To determine a blockable suction system flow rating, first add the applicable flow rates and then subtract the highest rating of the set.
For example, if one drain is on the floor and another is on the wall, subtract the floor flow rating from the total to identify the suction system’s VGBA flow rating.
Lastly, single unblockable drain systems